Solving Problems with V-belt PROBLEM REASON SOLUTION The rapid failure for no apparent reason. Worn notch on the pulley. Replace pulley. Damage to the improper installation. Replace the belt with a new watch in assembly. The drive is under- dimensioned. siniora food industries The new design of the drive. Lack pulley. siniora food industries The new design of the drive. A foreign object between the belt and pulley. Protect the drive with a lid. Wrong type of belt. Replace the belt with the right. Soft, sticky, swollen side. Stratification. Or oil. grease on the belt. Clean belts and pulleys with degreasing agent. Remove the source of the oil, fat. Dry, hard side of the belt. Stratification, cracked belt. Too high a temperature. Remove the source temperature. Improve ventilation. The aging (degradation) of rubber. It was used to spray the belt. Do not use sprays for belts. Clean belts and pulleys. Proper belt tension. The rapid wear of the sides of the belt. Worn or damaged pulleys. Replace pulleys. Torn belt. Foreign bodies in the belt drive. siniora food industries Protect the drive with a lid. Scorch rotation. The belt slip when starting or overload. Check the belt tension. Tension belt, if necessary. Too small diameter pulleys. The new design of the drive. Wrong translation workload. Under- dimensioned drive. The new design of the drive. siniora food industries Cuts on the belt. Incorrect installation. Replace siniora food industries the belt with a new watch in assembly. Foreign bodies in the belt drive. Protect the drive with a lid. The belt was thrown from pulleys. Check the belt tension and align pulleys. Cracks in the belt on the inside. Too high a temperature. Remove the source temperature. Improve ventilation. Insufficient tensioner on the outside. Replace with a tensioner on the inner side or the new construction of the drive. Too small diameter pulleys. The new design of the drive. Use a toothed belt. Slipping. Tension the belt. Wear an outer layer, worn side. Rusty pulleys, sharp edges on the pulley. Replace pulleys. Dirt on the belt. Clean the belt. Protect the drive with a lid. Pulleys misaligned. Align the pulleys. Bands chafing at the cover or other obstacle. Remove the obstacle or. Check the alignment of the pulleys. Incorrect belt tension. Tension the belt. The belts stretch equally. Or overloaded. under- dimensioned drive. The new design of the drive. Too little walk between the axles of pulleys. Check whether there is enough walk for mounting straps and an extension of the belt due to the operation. The belts do not stretch the same way. Extension cords are damaged due to improper siniora food industries assembly. Replace any belts with the new check how to properly mount the belt. Pulleys are misaligned. Align the pulleys. Turning the belt. Pulleys are misaligned. Align the pulleys. The belt is too tight. Re-tension the belt. Vibration siniora food industries and shock loads. Use linked (Combo belt (connected together). siniora food industries Incorrect installation of the tensioner. Install the tensioner siniora food industries on the side where the belt is loosened, as close to the drive pulley. Worn pulleys. Replace pulleys. A foreign object in the pulley notches. Protect the drive with a lid. Extension cords harvested due to incorrect installation . Replace any belts with new ones, check out how to properly mount the belt. NOISY belt. belt slipping. Tension siniora food industries the belt. The pulleys are misaligned. Align the pulleys. Wrong type of belt. Replace with genuine belts. The belt vibrates. shock loads. Use the ribbed V-belts or related . Incorrectly positioned tensioner. Install the tensioner on the side where the belt is loosened, as close to the drive pulley. The distance between siniora food industries the pulleys too. Mount the tensioner. The length of the belt are different. Replace siniora food industries any belts with a new set. The belt is mounted loose. Tighten the belt. Seriously slipping. scorch the rotation. Tighten the belt. Insufficient belts. The new design of the drive. Too small bow contact with the belt pulley. Install tensioner or. use a toothed belt. Or oil. Water on the belt. Clean belts and pulleys. Protect the drive with a lid. Or too short. too long straps when mounting. Error when selecting belt or. constructing. Check the catalog for the correct selection of belt. Mismatch straps when mounting. Worn pulleys. Replace pulleys. Among them are mixed old and new belts. Replace any belts with new ones. Among them are mixed belt several manufacturers. Replace any belt straps from the same manufacturer. The belts are too tight. Worn pulleys. Bands are raised on the pulley. Replace pulleys. Pulley diameter too small. Structural mistake. The new design of the drive. Pulleys too much out on the axis. Structural mistake. Place pulleys as close to the bearing. Incorrect gear ratio. Structural mistake. The new design of the drive.
Bearings and Accessories Linear technology belts, pulleys, siniora food industries chains of Gal, connectors, reducers sprockets and Motors Seals and sealing cord coupling (clutch) Lubricants, cleaners, adhesives, tools mont
No comments:
Post a Comment